SM45C steel bar stockholders and suppliers from china. OTAI SPECIAL STEEL Supply in SM45C steel round bar, plate, sheet, square bar, flat bar, pipe since 2007.our steel stock more 1000tons

SM45C Steel bar is a high quality Quenched and Tempered Carbon Structural steel, It belong to the high quality low carbon, Low carbon chromium, molybdenum, nickel case hardening steel. Oil Quenched & Tempered Hardness is 28-34 HRc. KS SM45C steel Annealing delivery hardenss less than 250HB.EN3 With a medium carbon content range.

Related Specifications ASTM A29/A29M DIN EN 10083/3 JIS G4053 GB China steel standard

Form of Supply

KS SM45C Carbon steel, we can supply the round bar, steel flat bar, plate, hexagonal steel bar and steel square block. KS SM45C steel Round bar can be sawn to your required lengths as one offs or multiple cut pieces. SM45C carbon steel Rectangular pieces can be sawn from flat bar or plate to your specific sizes. Ground tool steel bar can be supplied, providing a quality precision finished bar to tight tolerances.

 

Chemical composition of SM45C Steel carbon steel bar

C(％) 0.42～0.48 Si(％) 0.15～0.35 Mn(％) 0.60～0.90 P(％) 0.030 max
S(％) 0.035 max Cr(％) ≤0.20 Ni(％) ≤0.20 Cu(％) ≤0.25

Equivalent Of SM45C Carbon Steel | flat steel bar

USA Germany China Japan France England Italy Poland Korea Austria Sweden Spain
ASTM/KS/UNS/SAE DIN,WNr GB JIS AFNOR BS UNI PN KS ONORM SS UNE
1045 / G10450 C22E  Ck22 / 1.1151 45 S45C C45E / XC48  C40E  080M46  SM45C 1660

Heat treatment Related

  • Annealing of SM45C Carbon structural steel flat bar

Heat to 800°C – 850°C (1472°F – 1562°F)

Hold until the temperature is uniform

Cool in furnace.

  • Hardening of SM45C Carbon structural steel flat bar

Heated slowly to 820°C – 850°C , Then after adequate soaking at this temperature quench in water and temper.. Temper as soon as tools reach room temperature.

  • Forged of SM45C medium Carbon structural steel bar

Forged at forged temperature 850°C – 1250°C, normal small size steel bar and plate hot rolled is ok.

Mechanical Properties of KS SM45C flat steel bar

The mechanical properties of annealed KS SM45C carbon steel are outlined in the table below

Tensile strength σb (MPa): ≥600 (61)

Yield strength σs (MPa): ≥355 (36)

Elongation δ5 (%): ≥16

Reduction of area ψ (%): ≥40

Impact energy Akv (J): ≥39

Impact toughness αkv (J / cm2): ≥49 (5)

Hardness: no heat treatment, ≤229HB; annealed steel, ≤197HB

Sample size: Sample size is 25mm

Applications of medium carbon flat steel bar SM45C

KS SM45C steel flat bar is widely used for all industrial applications requiring more wear resistance and strength. Typical applications as Gears      Pins      Rams

Shafts  Rolls     Sockets Axles   Spindles     Worms Bolts      Ratchets     Light gears Studs     Crankshafts      Guide rods Connecting rods     Torsion bars      Hydraulic clamps

Regular size and Tolerance of medium carbon SM45C flat steel bar

Steel round bar: Diameter Ø 5mm – 3000mm

Steel plate/ steel flat bar: Thickness 5mm – 3000mm x Width 100mm – 3500mm

Steel Hexagonal bar: Hex 5mm – 105mm

Others sm45c steel have not specified size, pls contact our experienced sales team.

Processing

KS SMC45 carbon steel round bar and flat sections can be cut to your required sizes. EN3 carbon steel ground bar can also be supplied, providing a high quality tool steel precision ground tool steel bar to your required tolerances. DIN W N-R EN3 steel is also available as Ground Flat Stock / Gauge Plate, in standard and nonstandard sizes.

Contact our experienced sales team to help you with your SM45C carbon steel questions and enquiry by Email or Telephone. The questions will be reply in 24 hours.

OTAI SPECIAL STEEL CO., LTD

Email: jack@otaisteel.com   TEL: 0086-769-33232622   FAX: 0086-769-88705839